金湖凯铭仪表有限公司
顶装盐酸储罐液位计 侧装盐酸储罐液位计
产品属性
- 品牌:
- 其他
- 类型:
- 磁翻板液位计
- 型号:
- JKM-UHZ
- 测量范围:
- 0-1000mm
顶装盐酸储罐液位计 侧装盐酸储罐液位计产品概述<*n>
磁翻板液位计由本体、翻板箱（由红、白双色磁性小翻板组成）、浮子、法兰盖等组成，用于各类液体容器的液位测量。能用于高温、防腐、食品饮料等场合、作液位的就地显示或远传显示与控制。<*n>UHZ系列磁翻板液位计可以做到高密封、防泄漏和在高温、高压、高粘度、强腐蚀性条件下安全可靠地测量液位，全过程测量无盲区、显示醒目，读数直观，并且测量范围大，配上液位报警、控制开关，可实现液位或界位的上下限报警和控制，配上液位变送器可将液位。界位信号转换成二线制<*n>4~20mADC的标准信号，实现远距离检测、指示、记录与控制。<*n> UHZ系列磁翻板液位计广泛用于电力、石油、化工、冶金、环保、船舶、建筑、食品等行业生产过程中的液位测量与控制。
<*n>
顶装盐酸储罐液位计 侧装盐酸储罐液位计结构及原理<*n>
<*n>1、基本型<*n>:
根据浮力原理，浮子在测量管内随液位的升降而上、下移动，浮子内的*磁钢通过耦合作用，驱动红、白色翻柱翻转<*n>180°，液位上升时翻柱由白色转为红色，下降时由红色转为白色，从而实现液位指示。
<*n>2、电远传<*n>:
在浮子液位计上安装变送器，通过浮子上下移动，经磁耦合作用使导杆内测量元件依次动作，获得电阻信号变化，转换成<*n>0～<*n>10mA或<*n>4～<*n>20mA的标准信号输出，与显示仪表或计算机连接，达到远传目的。
<*n>3、上下限开关输出<*n>:
在液位计立管上由用户设定上、下限位置安装控制器，控制器内带有自保持作用的舌黄开关，利用磁性浮子随液位移动使*开关动作时，实现报警或限位控制。
系统构成及接线
<*n>1、上下限开关输出<*n>:
由具有自保持作用的舌黄开关和转换器组成，舌黄开关和转换器分别安装于现场和控制室，由转换器提供三对触点开关。
<*n>2、电远传<*n>:
由测量单元和变送单元两部分组成。
<*n>3、本安
<*n>a带本安上、下限开关输出型
开关由舌黄开关和带继电器触点的安全栅组成，可向用户直接提供一对常开或常闭触点。如用户需更多触点可特殊设计订货。
<*n>b带本安爆远传型
适合使用于∏类电气设备<*n>(工厂用<*n>)、<*n>C级气体，表面温度组别<*n>T4(135℃<*n>)。
<*n>c使用注意事项
①变送器外壳设有外接地，用户使用时必须可靠接地。
②安全栅的使用应遵守有关使用说明内容。
③变送器与安全栅本安端的连接电缆为二芯屏蔽电缆，芯线截面积＞<*n>0.5m，电缆允许分布电容为<*n>0.8μ<*n>F
<*n>
顶装盐酸储罐液位计 侧装盐酸储罐液位计的优点<*n>
<*n>1、结构简单、坚固牢靠、无需专门维护。
<*n>2、直接显示液位高低，不受被测液高温、易流动、*烧、*等特性的影响。
<*n>3、翻板工作无需电源，无需断开的情况下也能显示液位变化和报警。
<*n>4、可用于真空、高压、高温的环境，对密度低的液体也可适用。
<*n>5、耐腐蚀性能强，适用于大多数腐蚀性液体。
<*n>污水流量计 http://www.jhkmyb*
电磁流量计 http://www.jskmyb*
涡轮流量计 http://www.bubu8*
电磁流量计 http://www.w8w6*
涡街流量计 http://www.zhanfengdesign*
磁翻板液位计 http://www.fzyanlove*
顶装盐酸储罐液位计 侧装盐酸储罐液位计主要技术指标<*n>
<*n>1、量程范围（<*n>mm）：<*n>300～<*n>19000
<*n>2、介质密度（<*n>g/cm3）：<*n>0.5～<*n>2
<*n>3、介质粘度： ≤<*n>0.02Pa.S
<*n>4、工作温度℃：<*n>-40～<*n>350
<*n>5、压力等级（<*n>MPa）：≤<*n>32
<*n>6、测量精度（<*n>mm）：≤±<*n>10
<*n>7、安装方式：侧装式、顶装式、底装式
<*n>8、防护等级：<*n>IP65
<*n>9、等级：<*n>ibⅡ<*n>CT4（本安型）、<*n>dⅡ<*n>BT4（隔爆型）
<*n>10、传输方式：<*n>4～<*n>20mA 或 开关量
<*n>11、接口法兰：<*n>PN4.0 <*n>DN25 <*n>HG20593（侧装式）；<*n>PN1.0 <*n>DN100 <*n>HG20593（顶装式、底装式），可以根据用户的需要特殊定制。
注：当液位计安装受环境影响，空间位置<*n>L1<300订货时应明显提出。
<*n>
顶装盐酸储罐液位计 侧装盐酸储罐液位计应用须知<*n>
<*n>l、侧装式液位计与被测容器的上下分液管间各装一只截止阀门以便打开或关闭液位计；另一方面为维修液位计带来方便。在上下截止阀关闭时可打开液位计底部排污法兰或卸下排污螺钉，注入清水即可清洗液位计的主体。
<*n>2、安装液位计时，法兰中心线垂直度≤<*n>4‰，当液位计的测量范围大于<*n>3米时，需要考虑增加中间加固法兰<*n>(或朵攀<*n>)作固定支撑以增加强度。
<*n>3、配套远传液位变送器与二次仪表之间隔连线，要求连线的芯线截面面积应大于<*n>0.8mm。．与交流电源同路平行铺设时，至少应保持<*n>20厘米以上的间距，单独穿铁管铺设，或用屏蔽二芯电缆铺设，屏蔽层只能一端接地。
<*n>4、选用液位控制器，其触点容量均以阻性负载设计，如用非阻性或大力功率负载则要用中间继电器转换。
<*n>5、对液体介质中含有悬浮杂质的亲磁物质的场合，不宜使用本液位计，因这些杂质会对浮子组件造成卡阻。
<*n>6、外形结构中的盲区<*n>(L1)与介质密度有关。故不同介质有不同的盲区。
<*n>
顶装盐酸储罐液位计 侧装盐酸储罐液位计型谱<*n>
|
<*n style="font-size:9pt;font-family:宋体;">型 号<*n> |
<*n style="font-size:9pt;font-family:宋体;">结构特点<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">接液材质<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">测量范围<*n> |
<*n style="font-size:9pt;font-family:宋体;">适用介质条件<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">法兰连接<*n>(mm)<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">重量<*n>(kg)<*n style="font-size:9.0pt;font-family:宋体;"> |
|||||
|
<*n style="font-size:9pt;font-family:宋体;">温度<*n> |
<*n style="font-size:9pt;font-family:宋体;">压力<*n> |
<*n style="font-size:9pt;font-family:宋体;">密度<*n> |
<*n style="font-size:9pt;font-family:宋体;">粘度<*n> |
<*n style="font-size:9pt;font-family:宋体;">DN<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">PN<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">基本<*n> |
<*n style="font-size:9pt;font-family:宋体;">加长<*n> |
||||
|
<*n style="font-size:9pt;font-family:宋体;">C10<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">标准型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1Cr18Ni |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-2.45<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.0 |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">5<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C11<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高压型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">2.45-9.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">2.5 |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
|
|
<*n style="font-size:9pt;font-family:宋体;">C12<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高温型<*n> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">2.45-9.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6.3 |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
|
|
<*n style="font-size:9pt;font-family:宋体;">C13<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">低温型号<*n> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">>-40<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0-2.45<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6 |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">7.5<*n style="font-size:9.0pt;font-family:宋体;"> |
|
|
<*n style="font-size:9pt;font-family:宋体;">C14<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">液氨、液<*n> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-2.45<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.45-0.7<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.05<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">2.5<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6.5<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
|
|
<*n style="font-size:9pt;font-family:宋体;">C15<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">耐腐型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">00Cr17Ni14Mo2 |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-2.45<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">5<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C16<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">防腐型（<*n> |
<*n style="font-size:9pt;font-family:宋体;">PP<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">20 |
<*n style="font-size:9pt;font-family:宋体;">0-0.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">32<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">3<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">3<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C17<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">防腐型（<*n> |
<*n style="font-size:9pt;font-family:宋体;">U-PVC<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">20 |
<*n style="font-size:9pt;font-family:宋体;">0-0.5<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">32<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">3<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">3<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C18<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">防腐型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">ABS<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-0.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">32<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.0<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">3<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">3<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C19<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">防腐型（<*n> |
<*n style="font-size:9pt;font-family:宋体;">PP<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-1.0<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">4<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">5<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C20<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">防腐型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">PE<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">20 |
<*n style="font-size:9pt;font-family:宋体;">0-0.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.04<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">25<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">7<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C21<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">蒸气夹套<*n> |
<*n style="font-size:9pt;font-family:宋体;">1Cr18Ni9Ti<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-2.45<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.05<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">32<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">8<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C22<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高粘度<*n> |
<*n style="font-size:9pt;font-family:宋体;">0Cr18Ni9 |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-2.45<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.05<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">32<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">5<*n style="font-size:9.0pt;font-family:宋体;"> |
|
<*n style="font-size:9pt;font-family:宋体;">C23<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">食品专<*n> |
<*n style="font-size:9pt;font-family:宋体;">1Cr18Ni9Ti<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">300- |
<*n style="font-size:9pt;font-family:宋体;">-20 |
<*n style="font-size:9pt;font-family:宋体;">0-1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">0.5-2<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">≤0.05<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">50<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">1.6<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">7<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">5<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n>
|
<*n style="font-size:9pt;font-family:宋体;">□<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">配套仪表及附件内容<*n style="font-size:9.0pt;font-family:宋体;"> |
|||||||||
|
<*n style="font-size:9pt;font-family:宋体;">O<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">盲板法兰，不配排污阀<*n style="font-size:9.0pt;font-family:宋体;"> |
|||||||||
|
<*n style="font-size:9pt;font-family:宋体;">L<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">液位计底部配排污阀<*n style="font-size:9.0pt;font-family:宋体;"> |
|||||||||
|
<*n style="font-size:9pt;font-family:宋体;">O<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">无液位报警开关<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
||||||||
|
<*n style="font-size:9pt;font-family:宋体;">H<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高位报警开关<*n>AK-3型，有记忆功能，故障不排除，信号不消除<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
||||||||
|
<*n style="font-size:9pt;font-family:宋体;">L<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">低位报警开关<*n>AK-4型，有记忆功能，故障不排除，信号不消除<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
||||||||
|
<*n style="font-size:9pt;font-family:宋体;">B<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高位、低位报警开关全配，有记忆功能<*n>AK-3型和<*n>AK-4型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
||||||||
|
<*n style="font-size:9pt;font-family:宋体;">G<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高位报警开关，区域型报警<*n>AK-1型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">附<*n>DF-1型转换言放大器壹台<*n> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">D<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">低位报警开关，区域型报警<*n>AK-1型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
||||||||
|
<*n style="font-size:9pt;font-family:宋体;">Q<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高位、低位报警开关全配，区域型报警<*n>AK-1型贰台<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
||||||||
|
<*n style="font-size:9pt;font-family:宋体;">S<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">高位和低位一体化型报警开关，区域型报警<*n>AK-2型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
||||||||
|
<*n style="font-size:9pt;font-family:宋体;">O<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">无液位控制开关<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">H<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">上限控制开关，单点干黄<*n>CK-1型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">L<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">下限控制开关，单点干黄<*n>CK-1型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">B<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">上限、下限控制开关全配，单点干黄<*n>CK-1型贰付<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">W<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">上限、下限控制开关一体化，双点干黄<*n>CK-2型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">T<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">上限控制开关，霍尔型传感器<*n>CK-3型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">L<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">下限控制开关，霍尔型传感器<*n>CK-4型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">E<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">上限、下限控制开关全配，霍尔型传感器<*n>CK-3型贰付<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">C<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">上限、下限控制开关一体化，霍尔型传感器<*n>CK-4型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||||
|
<*n style="font-size:9pt;font-family:宋体;">O<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">无远传变送器装置<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||||
|
<*n style="font-size:9pt;font-family:宋体;">R<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">配<*n>LB型*式变送器，输出二线制<*n>4-20mADC<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||||
|
<*n style="font-size:9pt;font-family:宋体;">S<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">静压式远传变送器，（<*n>URS-100）输出二线制<*n>4-20mADC<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||||
|
<*n style="font-size:9pt;font-family:宋体;">O<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">普通防水型<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||
|
<*n style="font-size:9pt;font-family:宋体;">B<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">本质安全型<*n>ibⅡ<*n style="font-size:9pt;">CT4<*n style="font-size:9pt;font-family:宋体;">，可配齐纳安全栅或<*n>IS4041-Ex隔离栅<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||
|
<*n style="font-size:9pt;font-family:宋体;">Bd<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">隔爆型<*n>dⅡ<*n style="font-size:9pt;">CT4<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||||
|
<*n style="font-size:9pt;font-family:宋体;">O<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">不配远传显示仪表<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||
|
<*n style="font-size:9pt;font-family:宋体;">A<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">数字、光柱显示调节报警仪<*n> XGTH-510（竖式）<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||
|
<*n style="font-size:9pt;font-family:宋体;">B<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">数字、光柱显示调节报警仪<*n> XGTA-810（横式）<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||
|
<*n style="font-size:9pt;font-family:宋体;">C<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">数字显示调节报警仪<*n> XMTA-810（横式）<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||
|
<*n style="font-size:9pt;font-family:宋体;">E<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">双光柱液位显示仪<*n> XGH-202（竖式）<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||
|
<*n style="font-size:9pt;font-family:宋体;">D<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">智能型液位<*n>/容量（重量）显示调节仪<*n>XMT-620（横式）<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||||
|
<*n style="font-size:9pt;font-family:宋体;">-□□□□<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">测量范围<*n>(mm)<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|||
|
<*n style="font-size:9pt;font-family:宋体;">-□□<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">介质密度<*n>(g/cm3)<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
||
|
<*n style="font-size:9pt;font-family:宋体;">-<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">D<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">开口常压容器<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
|
<*n style="font-size:9pt;font-family:宋体;">□<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:9pt;font-family:宋体;">工作压力<*n>(MPa)<*n style="font-size:9.0pt;font-family:宋体;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n style="font-size:10.0pt;"> |
<*n>
售后服务
<*n>1、我公司所售产品在一年之内出现质量问题的（非人为），负责****维修。
<*n>2、质保期内如我公司产品出现任何质量问题，我公司负责****维修或更换。
<*n>3、质保期内如用户使用不当，造成产品损坏，我公司负责维修，收取损坏部件成本费。
<*n>4、如用户需我公司现场服务，我公司以****短时间到达用户现场。
<*n>5、本公司所售的产品所享受终生维护。