工程塑料合金MG系列滑板应用：

      1.大型新建铁路跨线、跨路、跨河施工，尤其以跨营业线施工更为常见； 2.大跨度、大吨位混凝土桥梁、钢桁梁顶推平移工程； 3.大型工厂、建筑物等工程的整体平移工程； 4.大型造船企业的船舶下水平移工程。

由于该产品具有很好的弹性、*冲击性和摩擦系数低等特性，能较好地消除轨道不平造成的局部高压带来的各种危害，因此特别适合于桥梁、水利、造船、工厂建筑物等行业的平移。

MG系列滑板桥梁顶推法滑板使用特性：

1.承载能力大：能承受较大的冲击或稳定荷载，当受到重击和撞击负荷时，由于其柔韧性强迫高弹态，能有效保护运转件和其它机构免受机械损伤；

2.摩擦系数低：摩擦系数小于有色金属和其他非金属材料，是干态、水态、油态工况条件下变化小，且动、静摩擦系数基本一致；

3.*损：比磨损率为10-7mg/Nm,比其他*非金属材料比磨损率10-6mg/Nm****了一个数量级，使用寿命大大****；

4.自润滑、免维护：具有良好的自润滑性，水可以作为它的润滑剂，也能够在干摩擦条件下正常使用；

5.具有弹性：自恢复性，吸振性，尺寸稳定性好，几乎不吸水，变形小；

6.不易脱落:*剪能力强，不会发生复合材料、橡胶、塑胶、胶木等材料产品的脱落情况；

7.加工性能好：既有韧性又有足够的硬度，机加工性与金属一致；

8.耐腐蚀：自润滑材料能抵*在电场、化学场、力场、及酸、碱作用下的各种介质的腐蚀作用，在酸、碱、盐水溶液（浓度在5%～25%）中浸泡，溶胀及溶出均小于0.03%～0.7%。 9.经济性能好：同其他金属材料相比较，使用寿命长，*，能给用户带来更好的经济效益；

MG系列滑板桥梁顶推法滑板优势：

据大量相关数据表明：传统聚乙烯板承受压力为6.4MPa,而MGE滑板承受压力为64MPa以上；单位平米的重量相比聚乙烯板而言要轻一半，有利于现场施工安装。同时还具有*、摩擦系数低、承载力大、*剪*冲击能力强、与滑块易于连接固定等特点，能够较好的消除因轨道局部不平带来的各种危害。

 friction coefficient and impact resistance, the product can eliminate all kinds of damage caused by local high pressure caused by uneve*ack, so it is especially suitable for bridges, water c*ervancy and shipbuilding. The translation of industries such as factories, buildings, etc.

The use characteristics of MG series skateboarding bridge pushing skateboarding:

1. Large bearing capacity: can withstand large impact or stable load, when subjected to he*y impact and impact load, because of its flexibility forced high elastic state, can effectively protect operating parts and other mechani*s from mechanical damage;

2. Low friction coefficient: the friction coefficient is *aller than non-ferrou*etals and other non-metallic materials, is dry, water, oil state conditi* change little, and dynamic, static friction coefficient is basically the same;

3. Wear resistance: the specific wear rate is 10-7 mg / Nm, which is one order of magnitude higher than that of other wear-resistant non-metallic materials (10-6mg/Nm), and the service life is greatly improved.

4. Self-lubricating, maintenance-free: has good self-lubricity, water can be used as its lubricant, but also can be used in dry friction conditi*;

5. Elastic: self recovery, vibration absorption, good dimensional stability, almost no water absorption, *all deformation;

6. Not easy to fall off: strong shear ability, will not occur com*ite materials, ru*er, plastic, Bakelite and other material products shedding situation;

7. Good processing performance: both toughness and sufficient hardnes*achinability is c*istent with metal;

8. Corrosion resistance: self-lubricating materials can resist corrosion in electric field, chemical field, force field, and variou*edia under the action of acid and base, soak in acid, alkali and salt water solution (conce*ation is 5 ~ 25%), swelling and dissolution are less than 0. 03 0. 7% 9. Good economic performance: compared with other metal materials, long service life, high performance-to-price ratio, can bring better economic benefits to users;

MG series skateboarding bridge pushing skateboarding advantages:

According to a large number of related data, the maximum bearing pressure of traditional PTFE plate is 6.4 MPA, while the maximum pressure of MGE slide plate is above 64MPa, and the weight per square meter is half lighter than that of PTFE plate, which is beneficial to site installation. At the same time, it also has the characteristics of wear resistance, low friction coefficient, large bearing capacity, strong shear and impact resistance, easy connection with slider and so on, which can better eliminate all kinds of harm caused by local uneve*ack.